Sign Making Supplies

Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts

Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts

Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts
Quality Foam Cutting Products Since 1991. Hot Wire Foam Cutting CNC Machine AERO Model.

Aero CNC 4-Axis Foam Cutting Machine. Proudly Made and Supported in the USA! Perfect for tapered airplane wings, architectural shapes, letters, and much more! The most user friendly and affordable USA made and supported 4-Axis CNC foam cutter on the market.

Fast and easy assembly of just 5 parts. Includes Mach 3 and Vector Linker software. Easily run it in 2-axis mode out of the box. Cutting Area: 48-inch Wire Length x 30-inch Horizontal Travel x 36-inch Vertical Travel.

Quiet and extremely accurate motion control. Extreme cutting precision with accuracy to. High-torque motors with rapid speed up to 200 per minute. Cutting speed is dependent on material and desired precision. Unique, low-maintenance design with minimal moving parts. Unlimited growth potential for advanced users. Hardware and software capabilities for complex prototyping. 99% Assembled Machine With Tools for Installation. We are located in Lompoc, CA. Our Hot Wire tools work best on rigid polystyrene foams, also known as expanded polystyrene (also known as EPS, Styrofoam or bead-board foam) and extruded polystyrene foam (also known as XEPS or XPS or insulation foam).

Polyurethane foam (aka upholstery foam) should not be cut with hot wire tools. It needs a ton of heat, gives off toxic fumes, and leaves a lot of melted plastic wherever it is cut. We recommend that the polyurethane foams only be cut with a blade or saw. Packages are always tracked and insured.

Will, at its option, repair or replace a defective unit free of charge, if the unit is defective due to an original manufacturers defect. Except as herein expressly set forth, HWFF, Inc. Shall not under any circumstances be responsible for any direct, indirect, incidental, or consequential damage resulting from the use of the equipment. The consumers sole remedy shall be such repair or replacement as expressly provided above.

DETAILS: Perfect for tapered airplane wings, architectural shapes, letters, and much more! The most user friendly and affordable USA made and supported 4-Axis CNC foam cutter on the market Fast and easy assembly of just 5 parts Includes Mach 3 and Vector Linker software. Easily run it in 2-axis mode out of the box Cutting Area: 48-inch Wire Length x 30-inch Horizontal Travel x 36-inch Vertical Travel Quiet and extremely accurate motion control Extreme cutting precision with accuracy to. 001 High-torque motors with rapid speed up to 200 per minute.

Cutting speed is dependent on material and desired precision Unique, low-maintenance design with minimal moving parts. Just keep it clean Unlimited growth potential for advanced users.

Hardware and software capabilities for complex prototyping INCLUDES: 99% Assembled Machine With Tools for Installation Assembly and Operating Instructions Motion Control Box PC with Pre-Installed Software Keyboard Mouse Power Supply 100' Extra Wire YOU NEED: Monitor 4-Axis CAM Software e. DevFoam LEAD TIME: Lead times vary. For more of our tools, check out our Shop. NOTE: Polyurethane foam (aka upholstery foam) should not be cut with hot wire tools. The item "Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts" is in sale since Wednesday, April 05, 2017.

This item is in the category "Business & Industrial\Material Handling\Packaging & Shipping\Shipping & Cushioning Supplies\Cutters, Dispensers & Racks". The seller is "hotwirefoamfactory" and is located in Lompoc, California. This item can't be shipped, the buyer must pick up the item.

  • Brand: Hot Wire Foam Factory
  • Model: CNC054
  • Type: Tabletop Cutter
  • Country/Region of Manufacture: United States
  • MPN: Does Not Apply


Hot Wire Foam Cutting 4-Axis CNC Machine AERO 3D Shapes Wings Aeronautical Parts